Home › Problems We Solve › Remote Pump Monitoring

Remote Pump Monitoring Systems for Water Wells & Pump Stations

Monitor pump performance, spot abnormal operating conditions, and get alerts before small issues turn into costly failures. NightOwl gives you remote visibility into motor vibration, amperage on each leg, run time, and start counts through one connected dashboard.

ngwa
NGWA 2026

Technology Award to co-founder Jim Blair

built by driller
Built by a driller

Installed by your well service company

one dashboard
One dashboard

Pumps, wells & tanks together

monitor or control
Monitor or control

Remote pump control with Ultra

A pump dies at 3 a.m. You hear about it at 8.

Most pump failures aren’t sudden. A bearing starts to wear, one power leg draws more current than the others, or a pressure switch makes the pump start and stop again and again. Without monitoring, nobody sees it. The first alert is a customer with no water, an empty storage tank, or a motor that’s already burned out.
By then you’re paying for an emergency call-out, a longer outage, and often a bigger repair than the one that was building for weeks.

Monitoring shows you the warning signs. When readings move outside the limits you set, NightOwl alerts you while the pump is still struggling, not after it has stopped. It can’t predict every failure, but it shows you warning signs that would otherwise go unnoticed.

desktop-imgs

What usually happens before a pump fails

Common pattern · varies by site

Wear begins

Motor vibration starts creeping up from bearing wear or misalignment.

Electrical stress

Current on one leg climbs or becomes unbalanced; voltage problems appear.

Cycling changes

Starts become more frequent as short cycling or dry-running sets in.

Failure

The motor trips or burns out overnight, with nobody on site.

Outage

No water, an emergency site visit, and an unhappy customer at 8 a.m.

Each of the first three stages produces a signal a remote pump monitoring system can track.

What Can You Monitor With a Remote Pump Monitoring System?

NightOwl brings the readings that matter most for pump health into one place. Choose the sensors that fit each site, then set alarm limits that make sense for each pump.

motor vibration

Motor Vibration

A dual-axis motor temperature and vibration sensor tracks changes in vibration and motor temperature that can point to bearing wear, misalignment, or other developing mechanical problems.

Watch for: a steady upward trend, or a sudden step change after service.

amperage on each leg

Amperage on Each Leg

Power monitors with current transformers read voltage and current on every leg of single- or three-phase supplies, so imbalance, dropped legs, and climbing amps
stand out.

Watch for: one leg drifting away from the others, or rising amps under the same load.

pump run time

Pump Run Time

Track operating hours and cycle history to see how hard each pump works and plan maintenance on real use.

Watch for: run hours that climb without more demand.

Pump Start Counts

See how many times a pump starts and how often. A rising start count is one of the clearest early signs of change.

Watch for: more starts per hour than the system normally needs.
dry run detection

Dry-Run Detection

NightOwl Ultra includes dry-run fault detection. Depending on the sensors installed, it can use readings such as electrical load, flow, pressure, or water level to flag a pump that may be running short of water.

Watch for: depends on site sensors and configured thresholds.
short cycle detection

Short-Cycle Detection

Ultra's run-time tracking includes short-cycle detection, flagging excessive start/stop activity that can point to a failing pressure tank, a switch problem, or a leak.

Watch for: alert thresholds are set per site.

Also on supported systems:

01

Voltage & power frequency

02

kW & power factor

03

Line shaft turbine oil

04

Pump house temp & humidity

05

Flow & pressure

06

Well & tank levels

See Your Pump Performance From Anywhere

Every pump reading lands in the NightOwl Live Dashboard, next to the wells, tanks, and other equipment on the same system. Check it from your desk, a tablet, or your phone.

status & aarms

Status & alarms

See which pumps are running, which have alarmed, and the alarm history for every site.

Electrical & vibration trends

Compare amps on each leg and motor vibration over time to spot gradual change.

run time & start history

Run-time & start history

Review run hours and start counts, with automated monthly reporting.

NightOwl · Live Dashboard

desktop-imgs
tablet-img
mobile-img

How NightOwl Remote Pump Monitoring Works

NightOwl brings the readings that matter most for pump health into one place. Choose the sensors that fit each site, then set alarm limits that make sense for each pump.
01

Connect monitoring sensors

Power monitors, current transformers, and vibration and temperature sensors connect to the NightOwl controller in the pump house.

02

Send data to NightOwl

Readings travel over cellular to NightOwl's cloud platform, on a schedule and when something changes.

03

View the dashboard

Check pump conditions, trends, and history for every site from the web dashboard or mobile app.

04

Get alerts & take action

Receive text, email, or app alerts when readings cross your limits. With Ultra, start, stop, or reset equipment remotely.

signal

Cellular connectivity

Ultra: 4G LTE in the US, Canada & Mexico. Flex: cellular with built-in Wi-Fi for on-site checks.

clock

Data intervals

Ultra logs every 5 minutes by default. Flex collects every minute and uploads every 15.

notification

Alert channels

Text/SMS, email, app, and dashboard alerts with configurable thresholds.

Want the technical detail? Read how sensors communicate with the NightOwl system.

Choose the Right NightOwl Pump Monitoring System

Both systems report to the same NightOwl Live Dashboard. The question is whether you need to control the pump remotely, or just watch it.
NightOwl – Ultra

Intelligent pump monitoring with NightOwl Ultra

Remote Monitoring + Control

NightOwl’s complete monitoring and control platform, built for water wells and pump systems.
Flex nightowl img

Smart Water Monitoring with NightOwl Flex

Remote Monitoring Only

A cost-effective way to monitor tank levels, pump activity, and water flow without control functions.

Compare

NightOwl Ultra

NightOwl Flex

Primary purpose

Complete well and pump monitoring and control
Flexible, cost-effective monitoring

Sensor inputs

2 analog, 4 digital/pulse, 8-port Modbus RTU
Up to 3 Modbus sensors

Pump analytics

Start counts, cycle tracking, short-cycle & dry-run detection
Pump activity monitoring

Remote control

✓ Two relay outputs
✕ Not available

Alerts

SMS, email, dashboard
App, email, text

Power

120 VAC
12 V DC

Typical use

Pump houses, community & commercial systems, municipal & industrial sites
Homeowners, HOAs & utilities that need visibility without control

Need tank monitoring too? Compare all three in NightOwl Flex vs Ultra vs TLM, or configure a setup in the System Builder.

Remote Pump Monitoring for Different Water Systems

The same pump readings help different people in different ways, from a single well owner to an operator responsible for dozens of sites.
water wells

Water wells

Watch the pump next to well water level, so you can tell whether a problem is the motor, the power supply, or the aquifer.
agricultural pump

Agricultural & irrigation pumps

Check run time and pump status on irrigation wells spread across a property without driving to each one. See irrigation monitoring.

community water

Community water systems

HOAs and small community systems get early warning on the pumps everyone depends on, plus monthly reports for the board.
commercial water system

Commercial water systems

Businesses on private wells can track pump health and power use, and keep their service partner in the loop.
remote water stations

Remote pump stations

Remote pump station monitoring covers power, vibration, and alarms at unattended sites, with remote reset on Ultra.
multi site water infractructure

Multi-site water infrastructure

Drillers, pump companies, and operators see every site in one dashboard instead of juggling separate logins.

Why Monitor Your Water Pumps Remotely?

Remote monitoring turns pump maintenance from guesswork into a plan. You see what each pump is doing, and when it starts to change.
earlier visibility

Earlier visibility

See conditions that often come before a failure, while there’s still time to act.
fewer site visit

Fewer site visits

Check readings first, and drive out only when there’s a reason to.
better maintenance planning

Better maintenance planning

Schedule service around run time, starts, and trends, not the calendar.
clearer operating picture

Clearer operating picture

Know how every pump is running every day, not just on inspection day.
faster response

Faster response

An alert arrives before the customer complaint does.
centralized monitoring

Centralized monitoring

Wells, tanks, and pump stations across many sites, in one view.

Why Choose NightOwl for Remote Pump Monitoring?

NightOwl was co-founded by a Texas well driller and is installed by the drillers and pump companies that already service the well. It’s built around how water wells actually run in the field.

NGWA 2026 Technology Award

Co-founder Jim Blair, owner of Bee Cave Drilling, was recognized for contributions to groundwater tools, well construction, and service. Read the story

Built around real water wells

Designed by people who drill and service wells, not adapted from another industry.

Wells, pumps & tanks in one view

Pump data sits next to well level, tank level, flow, pressure, and water quality.

Flexible sensor setups

Start with the readings you need now, then add power, vibration, or flow sensors.

Monitoring or monitoring + control

Choose Flex for visibility, or Ultra for remote pump, valve, and power control too.

Try before you commit

Service partners can test equipment through the NightOwl loaner program.

Proven with service partners

Read how drillers and pump companies use NightOwl in our success stories.

Remote Pump Monitoring Questions, Answered

Quick answers about how NightOwl monitors pumps, and how Ultra and Flex differ.

Still have a question?

Talk to the team about sensors, installation, or the loaner program.

Remote pump monitoring uses sensors and a connected controller to measure how a pump is running, such as current draw, vibration, run time, and starts, and sends that data to a dashboard you can check from anywhere. Alerts tell you when readings move outside normal limits.
Sensors in the pump house connect to a NightOwl controller, which sends readings over cellular to NightOwl’s cloud platform. You view the data in the NightOwl Live Dashboard and get alerts by text, email, or app when a threshold is crossed.
NightOwl can monitor motor vibration and temperature, voltage and amperage on each leg, power frequency, run time, and start counts. Systems can also include flow, pressure, well and tank levels, and pump house temperature and humidity.
Yes. NightOwl Ultra includes dry-run fault detection and short-cycle detection. How each one works depends on the sensors installed at the site and the alarm thresholds you configure, so we set it up with you during system design.
Yes. NightOwl power monitors with current transformers report voltage and current on each leg, and a dual-axis motor temperature and vibration sensor reports motor condition. Both appear in the dashboard with their history.
NightOwl Ultra is a monitoring and control platform with relay outputs and built-in pump analytics. NightOwl Flex is monitoring only, supports up to three Modbus sensors, and has no relay outputs.
With NightOwl Ultra, yes. Its relay outputs let you turn pumps on or off and reset valves and power from your phone or computer. NightOwl Flex does not offer control.
Yes. Ultra and Flex both support multi-site monitoring, so you can see every pump station, well, and tank in one dashboard, with access for multiple users.
Intelligent pump monitoring goes beyond displaying raw readings by continuously analyzing pump performance trends and automatically identifying potential faults. It helps detect early warning signs of mechanical issues, allowing businesses to take proactive action, reduce unexpected downtime, and improve equipment reliability.

Know What's Happening With Your Pumps Even When You're Not There

See how NightOwl can help you monitor pump conditions, spot unusual operating patterns, and manage your water system with more confidence.